Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
Right here in the next paragraph you might get some awesome insight in regards to A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old tub is easily obtainable, the project can move speedily; if you have to open up a wall to eliminate the old bathtub and also position the brand-new bathtub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. See to it you have qualified yourself for the work and are comfortable trying it. As opposed to working with a service provider to take over a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you may require a professional plumber to make tube links.
This post will certainly aid you mount a new bath tub in your restroom if you have currently purchased a brand-new tub as well as don't need to transform the setup of your previous supply of water pipes.
Your devices and also product list ought to consist of the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the limited access that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bath tub in the required position. The wood boards are useful in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system as well as inspect all joints and new pipework for leakages and tighten them if needed. Fill up the bath tub and also examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and securing around the tub needs to wait till the tub has been utilized at the very least when as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers are in place in between the tap as well as the sink. Secure the tap in position with the supplier given backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap connectors. The previous type ought to be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break a stiff seal, causing the water to permeate the wall surface between the bathroom and also the tiling, causing difficulties with moisture and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to enable the motion experienced when the tub is in usage. The sealant can break fairly early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very excited about Tools You Need to Install a New Bathtub and I am hoping you enjoyed our entry. Are you aware of somebody else who is in the market for the subject? Feel free to promote it. We treasure reading our article about How to Install a Bathtub Yourself.
Quick fix? Dial now. Report this page